- CLOVER CONFIGURATOR HANGS ON CONFIG.PLIST SAVE INSTALL
- CLOVER CONFIGURATOR HANGS ON CONFIG.PLIST SAVE DRIVERS
- CLOVER CONFIGURATOR HANGS ON CONFIG.PLIST SAVE DRIVER
- CLOVER CONFIGURATOR HANGS ON CONFIG.PLIST SAVE FULL
- CLOVER CONFIGURATOR HANGS ON CONFIG.PLIST SAVE MAC
By default, we need to make adjustments here, and this requires a bit of experimentation.
CLOVER CONFIGURATOR HANGS ON CONFIG.PLIST SAVE DRIVERS
If any of the drivers in the BIOS or UEFI folders (from the drivers folder) are deleted, you can simply copy any missing drivers over from that "off" folder. All of these drivers and more are located in the folder EFI -> CLOVER-> drivers -> off. These are a list of minimal drivers needed to boot. Having an extra copy also saves time in the event that it gets accidentally deleted. Control + drag each kext from its unzipped folder to the My Kexts folder (or whatever you named it) in order to copy, not move, each kext.įrom that point on you can go to your My Kexts folder and copy and kexts there to the flash drive.Designate a new folder for kexts and label it "My Kexts" (for example).To save time from having to copy each kext from each of the unzipped kext folders, I copied these to new a folder on my hard drive to make it easier for dragging and dropping the next time.
CLOVER CONFIGURATOR HANGS ON CONFIG.PLIST SAVE FULL
HELPFUL HINT: When I was setting up the installer for my AMD machine, I ended up using different flsh drives to test because the Catalina full installer didn't work nor did the Catalina Recovery Installer, and I had to then try the versions for Mojave. This way you can move kexts in and out later on. If there are other kexts you want to test, you can go to BOOT -> EFI -> Clover -> kexts and make a separate folder called "unused", "Not used" or similar (the OS won't look for those types of filenames) and keep any extra kexts there to experiment. If it uses one of the types listed above, you're in luck! Else, you can purchase a USB-to-Ethernet adapter for $20 or less and it should work. No matter what computer or board you're using, go the manufacturer's product page to get the specs and see what type of networking set it uses.
The last essential piece for now is the one for networking, as the installation process requires a connection. Initially it won't work when you have your Hackintosh booting freely but will be used afterwards.
CLOVER CONFIGURATOR HANGS ON CONFIG.PLIST SAVE MAC
Windows users will have to right-click the file and unzip it whereas Mac users just double-click the. From here on out, the process for kexts will be the same for both Windows and Mac users. Since we're on the subject of kexts, let's get these out of the way. Alternatively you can simply perform a Google search for the kext(s) you need and get the latest versions just in case they are not quite updated on the above link. These can be downloaded from the link here:īookmark this page so you can refer to it if and when you need more kexts.
The ist file and the drivers folder were generated automatically when you installed Clover. Not only is this done for compatibility testing, but allows for more control as the Clover bootloader provides limited ability to change parameters after the computer has been booted. The editing process lets you modify the files before installing macOS.
CLOVER CONFIGURATOR HANGS ON CONFIG.PLIST SAVE DRIVER
We won't be modifying and data in any driver, but simply moving driver files around in order to get it working.
CLOVER CONFIGURATOR HANGS ON CONFIG.PLIST SAVE INSTALL
ist - This is the primary file that gets loaded when you select the MacOS drive after booting, whether it's the one used to install MacOS or the one used to load the drive with MacOS after it's been installed.Now that you have the operating system and Clover on your flash drive, the next steps involve adding and modifying the Clover files so that it can boot properly for your machine.
0 kommentar(er)
